Raw Basic Centrifuge

Description

The Raw Power Centrifuge eliminates the need for filtering, settling, pumping,
pressure and headaches. We have developed that special, reliable and trusty tool
that once you have it in your hand, you can’t live without. In three short hours
35 gallons of wvo is ready to be used as fuel.
This centrifuge has the ability to produce fuel quality oil from a variety of
waste oils including waste motor oil, wmo, waste vegetable oil, wvo, ATF,
hydraulic oil and basically any kinds of waste oils.
This centrifuge spins at 3450rpms and produces 1200 units of G-force. The
dirt and water get trapped in the centrifuge bowl, while the clean oil sprays
out over the top, collecting on the sides of the housing, then flowing out the
drain tube. The centrifuge bowl is 8” outer diameter and will hold 22ozs of
contaminants. The bowl will need to be cleaned approximately every 300 gallons.
This centrifuge works by applying g-force to a liquid, causing a settling of
the denser particles and fluids to occur. Water and dirt are heavier than oil,
so the centrifugal forces pull the unwanted particles and liquids out of the
oil. This allows you to safely burn the oil in a diesel vehicle or convert into
biodiesel.
The Baldor 1/3hp/150watt motor is custom made in the USA and features special
upgrades for use with waste oils. Sealed bearings and a special channel have
been added to protect the motor.
The unique lid design aids in the removal of water. Water is a primary target
when cleaning oil. This unique design allows you to vent off water that turns to
steam when heated or that happens to make it out of our bowl in the mist spray.
This centrifuge is gravity fed and designed to be a single pass system. No
messy filters to buy, change or monitor.
It is recommended to heat the oil to at least 150F for better separation
which will allow a flow rate of 15gph. Ideal temperature range is 150-200
degrees F. Non-heated oil can be used, but not nearly as effective. This will
lower the flow rate to 5gph or lower depending on the temperature and the
quality of the oil.
Some assembly required and is offered in 120 volt only.
1 Year Limited Warranty:
This centrifuge comes with a free replacement
of any part that wears out or breaks during the first year. This warranty
includes seals, latches, bearings, cast structure, and the rotor. Labor for
repair and shipping is not included.
5 Year Replacement Warranty On Major Components:
Our centrifuge comes
with a 5 year replacement warranty on non wear items such as bearings, seals and
brushes. Shipping is not included.
Optional Heater:
1000W Bolt on Immersion Heater
~Thermostat of
60-250F degrees
~Custom Cast Aluminum Heater manifold
~Two 3/4″ NPT to
Hose adapters
~One 3/4″ NPT Plug
~1ft 3/4″ High Temp Silicone Heater
Hose
~Two 1″ band clamps
~Does not include power cord or switch
~1
year warranty on heater
~Additional $297.00
(available at our Store)
Optional Booster:
Designed for the Raw Basic & Extreme Centrifuges
to increase efficiency and allow for the ultimate cleaning performance. This
booster maintains an easy and quick cleaning ability of the open bowl design.
The oil starts spinning prior to entering the centrifuge bowl which will
reduce the turbulence in the bowl. Also, the booster feeds the incoming/dirty
oil into the bottom of the centrifuge bowl, forcing the dirty oil to have to
work it’s way through the entire batch of existing oil in the bowl.
Bolts on
to rotor with no modifications and does not need to be removed when cleaning the bowl.
Requires feed through center port.
Additional $100.00 (available at our Store)
Return policy:
30 days from date on Invoice
Original shipping charges are not refundable
Return shipping paid by Buyer
Must be in new condition; no used items will be accepted
Items ship via Fed-Ex; please allow 3 days for item to ship
Shipping charges are for Continental USA only,
please contact us for specific cost for other locations.
Thank you for visiting our Store!